Gutters – Typical Problems and Solutions

A – GUTTERS AND ITS IMPACT ON THE INTEGRITY OF A BUILDING

Gutters have one function: collect rain running off a roof and channel it, with proper slopes, to downspouts that carry the rain water to the ground and away from the façade and foundations. Even though they’re “out of sight and most of the times out of mind” for the majority of the time, gutters actually play a huge role in the structural integrity of any building.

A clogged or leaking gutter can represent serious problems such as structural damages or health issues. Despite of this, most of the times it can be too easy to forget about them until something goes wrong – and at this stage the cost of any repair would be much higher than if a regular maintenance program was installed and problems were detected at an earlier stage. Experience show us that in most of the cases gutters suffer a quick deterioration, much quicker that the roof and the remaining of the building, requiring repairs or integral renovations in order to maintain its function for as long as the building service life.

When defining solutions to avoid the need of gutter repairs, it’s important to remember one simple fact: clean gutters are far less susceptible to deterioration than blocked gutters. In fact, the two most common gutter related topics facing building owners are blockages in the gutter itself, and blockages in the downpipes. These blockages are often caused by debris like fallen leaves, moss and other developed vegetation, and (in some undesirable cases) dead animals.

B – COMMOM GUTTER PROBLEMS

An Inadequate Gutter System

The specification and installation of a proper gutter system is key in order to avoid future problems. The choice of design, base material, and other particularities of the final solution, should take in consideration the project location, the gutter area of influence, and other aspects such as the existence of trees on the surrounding, otherwise it will not address properly the challenges to which it will be submitted during its lifetime, and will most probably fail prematurely. Improper location of downspouts, or not having enough of them, can lead to standing water and overflows during heavy rains. Standing water will cause among other: erosion, rust, siding damage and damage to the gutter support system and roof from excess weight.

Inadequately Pitched Gutters

In order for water to flow properly, gutters need to be angled accurately. The slope should sit at the correct angle. Possibility of standing water should be completely avoided – standing water will promote a quicker deterioration of the gutter – no matter of which is the gutter base material.

Gutters not Draining or Clogged Gutters

The most common problem we see with gutters is clogging. When gutters become clogged, they can’t drain properly and can start to overflow during rainstorms. When the water can’t flow properly, it can start to cause problems. That’s why it’s so important to keep gutters clean — the water must to be able to flow through easily. Clogged gutters cause water to stand and stagnate and often overflow. As we have seen before possible consequences of stagnate water are among others: erosion, rust, roof damage, siding damage, and damage to the gutter and roof support system from excess weight.

Leaking gutter joints

Leaking gutter joints are another common problem: in fact, leaking gutters are one of the most common causes of isolated damp in building’s interiors. Leaks can occur when bits of debris get caught in the joints, or simply from general wear and tear. As in any situation joints are critical points, and special care should be taken when defining solutions for joints or with its maintenance.

Damaged Gutters

Gutter damage can happen by various causes – the most common being the weather. During a heavy rainstorm or windstorm, gutters can be knocked down or damaged. In this case, it might be necessary fixing them, or to replace certain sections. In this case, there’s not much one can do to prevent it, other than making sure your gutters are properly installed and aren’t already loose.

Sagging Gutters

For clogged gutters with debris, moss, and standing water, overflowing water isn’t the only problem. The extra weight can also cause gutters to sag. This is usually caused by loose hangers or hangers too far apart, which pull out when they can’t hold the extra weight. This can usually be fixed by simply tightening the screws again, or installing new ones, ensuring the necessary mechanical resistance.

Corrosion

Corrosion on metal gutters will be a consequence for any of the problems identified earlier. It can also appear due to other causes: gutter sections are typically bolted together and this is where the problems start. Fabrication and welding processes destroy the gutter coating requiring local post manufacturing treatment to restore corrosion resistance – most of the times this is not done properly and corrosion will start here. Also gutter systems are usually the first part of the building envelope to be installed after the construction of the frame. The result is that the gutter is used as an access way and / or storage area during the roof construction causing surface damage and wear even before building use started – at these points the material will become fragile and there is an increased probability for corrosion to appear. If left untreated, corrosion continues – it will continually eat into the surface, the exposed cut edge of the sections and the fixings.

Failures in any system will always become evident at its weakest point, which in a gutter system is going to be the joints and changes of direction. Once corrosion has set in and a joint has started to fail, building movement, thermal expansion, freeze/thaw will further exasperate the problem. Once a joint has opened up it can be difficult to fix because of the build-up of dirt, debris and moisture around the opening.

C – MAINTENANCE IS KEY

Industrial or residential rainwater gutter systems are designed to give many years of reliable service but to achieve this, a regular inspection and routine maintenance program should be undertaken. Prevention is always better than cure and establishing a regular maintenance program is the most effective way of ensuring that serious problems do not arise.

In the course of collecting water, open rain gutters also collect leaves, acorns, pine needles, and other debris which can cause clogs anywhere in the gutter itself or sometimes in the downspouts. In dry conditions clogged gutters are a fire hazard; and during heavy rains, clogged gutters and downspouts can cause rainwater to overflow, potentially causing substantial damage to the building. To keep gutters free of debris, a maintenance program has to be defined. This might vary depending on the climate, but usually, it’s a good idea to maintain at least a twice a year program – clear them out in late fall after most of the leaves have fallen, and in spring to make sure they’re clear for some showers. On locations where the existence of particularities that contribute to a higher probability and quantity of debris inside the gutter, such as for example, the existence of many trees on the surrounding area or the existence of seagulls frequently on the roof, it may be necessary to clean the gutter more frequently.

First of all it is necessary to define the periodicity of the maintenance program depending on the building specificities. Secondly, it is important to define clearly a checklist for any maintenance operation. All maintenance operations should consider at least the following tasks:

  • Clean leaves and debris from the inside of gutters
  • Clean all downspouts, elbows, and joints

In addition to this, and depending on the project and gutter age, the following tasks should be considered:

  • Verify all gutter joints
  • Verify screws and all fixing / holding elements
  • Look for excessive movement and re-secur or re-pitch when necessary
  • Look for parts and accessories that may need to be replaced in order to keep them functioning properly
  • Install extra screws or hidden brackets to extend the life of the system a little longer
  • Look for signs of rust and address properly these areas

 

D – WHEN REPAIRS OR RENOVATION ARE REQUIRED: SOLUTIONS

When simply due to age, or due to more specific causes such us improper maintenance, it might came to a scenario where a more deep intervention has to be considered: it might be the case for an intervention with focus only on the gutter joints, or some other specific points, or of an integral renovation of the gutter.

Typical solutions

The most common used solution for gutter repairs or gutter renovations are liquid Installed Solutions. The most frequent difficulties associated with such solutions are its limitation to handle movement – and movement on gutters can be quite significant. Usually such solutions, in order to function properly, need to be applied carefully: the correct thickness of each layer should be respected. The problem is that on such constrained area as a gutter, it is quite hard to assure that a specific thickness of material is being applied, and to maintain this same thickness at all areas where the material is being applied. Typically, if the thickness applied is higher that the recommended, the elasticity of the material will not be able to absorb the expected movement and it will fail; if the thickness of the material is lower than the recommended it will not have the necessary resistance and it will fail prematurely.

If we analyze the offer for non-liquid Installed Solutions, we can find some solutions on the market with membranes, that are specifically promoted for gutter waterproofing. With membrane solutions usually the quality of the material and its performance is easier to control as this is factory controlled. The downspout of such solutions is that they usually require specialized tools for installation and very specialized labor. As conclusion we may say that there is a lack on the market for efficient, sustainable and easy to install solutions for gutter repairs or renovation.

 

The Effisus Solutions – A step further

1 – Effisus Titegutter3 – Integrated system for sealing gutter joints

Effisus Titegutter3 is the innovative integrated system for sealing gutter joints. The system’s efficiency and added value are guaranteed by its three waterproofing levels. Their properties give it the capacity of accommodating joint movements originated by structural or thermal expansion.

The system solves, in an efficient and sustainable manner, the common gutter joint sealing job. Due to its speed and ease of application, the job can be done without the need of specialized labour and its completion time is largely reduced. With Effisus Titegutter3, one can reduce the probability of human error, reduce application time and assure gutters’ waterproofness.

Effisus Titegutter3 – Characteristics:

  • Exceptional adhesiveness
  • Increased ageing resistance
  • Application temperature from -5ºC to +35ºC
  • Fully customisable
  • Permanently flexible
  • Resistant to structural and thermal expansion
  • No need for soldering or heavy machinery

Level 1 Effisus 2Bond DS Tape

  • 100% waterproof and both air and moisture tight
  • Active sealants with exceptional adhesiveness
  • Double-sided adhesive tape

Level 2 Effisus Ecofacade Membrane and Effisus Bonding KF+P Adhesive

  • Resistant to UVs and extreme temperature variations
  • Recyclable and with an elongation of up to 300%
  • Tough, puncture resistant and 100% waterproof

Level 3 Effisus Bonding KF+P Adhesive

  • Permanently flexible
  • UV resistant

2 – Effisus Alltitegutter – Waterproofing liner for gutter repairs

Effisus AllTiteGutter is a waterproofing membrane for the repair of deteriorated gutters. It is a very flexible and self-adhesive EPDM waterproofing membrane, featuring state of the art technology, that brings everlasting sealing security to the most critical parts of the roof – gutters.

A gutter is usually the first area of a roof to get seriously damaged. At the same time it is an area that is quite often difficult to repair with traditional methods or materials – there are limitations of spacing to work, sharp edges, high movements, etc. Effisus AllTiteGutter is the ideal solution to overcome such challenges and assure a waterproofing gutter, with an easy and quick installation method. Details are quickly solved in conjugation with the Effisus Bond FT Tape.

Effisus AllTiteGutter – Characteristics:

  • Self-adhesive EPDM membrane
  • No limitations on dimensions
  • Fully customisable
  • Expected service life of 50 years
  • Service temperature from -30ºC to +120ºC
  • Permanently flexible
  • Unaffected by permanent contact with water
  • Resistant to structural and thermal expansion
  • No need for soldering or heavy machinery

QUICKER, EASIER & SAFER

If you want to receive more information about Effisus services or products, please subscribe our Newsletter. 

18 Comments

  • Buongiorno,
    Interessante e innovativo, inserirò nei capitolati il prodotto.
    Team ___gfquarti

  • Sarah Smith says:

    Our gutters have always had a bit of standing water in them, and I thought that was the norm. Your information that this actually causes faster gutter deterioration is really helpful. We’ll start looking into gutter specialists who can help us remedy our gutter pitch.

    • Avatar photo Effisus says:

      Thank you for your feedback. May we suggest you Effisus AllTiteGutter, a waterproofing membrane for the repair of deteriorated gutters. Effisus AllTiteGutter . Feel free to send us details to better help you.

  • KARTIK S RAJAN says:

    We find your solution for gutters very interesting and are looking for similar products with multifarious applications. We are in the business of providing waterproofing solutions in Southern India. We look forward to an association with you and request you to please send us the information of your product range with prices, availability and relevant details.

  • I found this article very interesting. Thanks for the ideas you’ve shared. This article helps a lot .

  • It would never have occurred to me that corrosion affecting my rain gutters would be something I would need to worry about. I don’t think my gutters have ever had any service performed on them. I should probably call a professional to come and inspect them.

    • Avatar photo Effisus says:

      Thanks Dennis for sharing your thoughts… Indeed gutters are a critical element of a building and require maintenance for greater longevity. Stagnated water, inadequate slope installation and debris accumulation can always occur, with great impact on performance and longevity. Gutter joints are by nature the weakest points and should performed properly and special maintenance care ensured. In case we can further support, please do not hesitate in contacting us: [email protected]

  • Tom Spry says:

    Keep up the great work! Thank you so much for sharing a great posts.

    • Avatar photo Effisus says:

      Many thanks for you comment. We are working on new contents to share regarding typical weatherproofing challenges on the building envelope. Meanwhile please feel free to get in contact with any enquiry you might have.

  • Matt Worthy says:

    Great post. It’s amazing how many well-kept homes I come across that have neglected their gutters!

    • Avatar photo Effisus says:

      Dear Matt, Many thanks for your feedback. In fact, gutters are neglected many times, despite their so important role on the durability of the building.

  • I like how you mentioned that gutters can prevent your property to get damaged but that they also need maintenance. My parents told me that their roof is getting water filtration and they would like to find a way to solve that issue. I will recommend them to contact a company that can install gutters so that their roof won’t get more damaged.

    • Avatar photo Effisus says:

      Dear Derek,

      Many thanks for your comment. In fact, without proper maintenance, gutters will deteriorate much quicker, with an increased risk for water infiltration. Roof penetrations for passage of pipes, ducts or cables are another common cause for roof leaks (when not properly sealed).

  • Excellent post. I want to thank you for this informative read; Gutters – Typical Problems and Solutions I really appreciate house cleaning tips sharing this great post. Keep up your work. You can also visit this website https://www.elitewaterblasting.co.nz/ for convenience. I think you made some good points in this post.

    • Avatar photo Effisus says:

      Many thanks for your feedback – this is really important for us. We are currently working on new content that we should share online on next weeks – this will include some other valuable tips for building maintenance.

  • Thank you for sharing these important and useful tips, you have answered many of my questions… these are some real time issues regarding gutters to deal with, I am so happy to come across your blog..I was really looking for this…

Leave a Reply